While power seems relatively unchanged, the increased ergonomics and features make for a tremendous upgrade. The conclusion can only be that the newly updated Milwaukee M12 FUEL impact driver and hammer drill are superior to the older models in nearly every way. Both it and the former model have a good balance, but the space savings of the Milwaukee 2553-20 make it easier to fit into tight spots. I like the new M12 for its better ergonomics. It not only did a great job removing the old deck boards, it speedily drove in over a pound of new 3-inch decking screws. Grabbing the updated Milwaukee M12 impact driver and some decking screws, we set to work. Rather than replace the decking with 5/4 boards, we went straight to pressure-treated 2×6’s. ![]() Needless to say, it didn’t pass our safety standards. It had a rotten wood beam and decking that you could just about put your foot through. We had a children’s playground that desperately needed an update. Needless to say, both drills are within 4% of each other and within 7% of the manufacturer’s claims. It’s also in flux as we build a more permanent and robust testing apparatus. ![]() While our numbers didn’t perfectly match those of Milwaukee, the fact is-we’ve got a different setup than they do. We put both M12 hammer drills into our torque testers and measured the following: Carrying around 12V tools as your “everyday carry” only works of those same tools can get the job done. Milwaukee M12 FUEL Hammer Drill and Impact Driver Performance Since the mode switch integrates into the clutch mechanism, you don’t shave any more length off the tool. What About the Milwaukee 2503-20 M12 FUEL Drill? Interestingly, the Milwaukee 2503-20 drill comes with the exact same specs and size as the 2504-20 hammer drill-just without the hammer function. To give you a quick side-by-side on specs, here are the differences between the new tools: Milwaukee M12 FUEL Impact Driver and Drill Specs Compared ![]() The housing cover alone uses seven 16mm T-10 Torx screws. The tool seems like it can take some drops and keep running. Having experienced more than one assembly line where products like this are made, the wiring assemblies and “trap” locations seemed intelligently placed to keep them from moving parts. That includes the mainboard and selector switch assembly. All of the PCBAs (printed circuit board assemblies) are securely nestled into the glass-reinforced nylon body. Within the stator on the Milwaukee 2553-20 and new 2504-20 hammer drill, for example, you can find a large 7-point star-driveshaft that moves the gear assembly. The build quality of these new tools is excellent as far as we can tell. That kit (2598-22) is priced at around $229. The new M12 tools ship with either one or both Milwaukee RedLithium 2.0 or RedLithium 4.0 XC battery packs. That means your grip won’t change, and the balance-which we already felt was good-remained excellent. Milwaukee opted to keep the same raked angle on both their M12 FUEL impact driver and brushless FUEL hammer drill. Milwaukee 2504-20 vs 2404-20 Hammer Drill: Size Matters The Milwaukee M12 hammer drill came in third in our best 12V cordless drill roundup, and the M12 impact driver won our best 12V impact driver review comparison. ![]() The first-generation M12 tools performed well. What you should want to know, above all, is what’s changed between the first-generation tools and the newest Milwaukee M12 FUEL impact driver and M12 FUEL hammer drill. See our article on Drill vs Impact Driver and Speed vs Torque in drills and impact drivers Milwaukee FUEL vs 1st-Gen Models It’s been a long time coming, but Milwaukee seems to have found the special sauce for a ripe combination of size and strength in its M12 drills and drivers. It’s finally shorter and also shaves 1.2 ounces off the weight. Why was this significant? Well, the 12V Milwaukee FUEL was priced lower and weighed just 1 lb 14 ounces, but the 20V DeWalt DCF895B was a full 3/4-inches shorter in length!įast forward to today, and the new Milwaukee FUEL 1/4” impact driver (2553-20) shrinks its length down to just 5.1-inches. At about the same time the original brushless M12 impact driver and other tools were announced, DeWalt released its DCF895B 20V Max brushless 3-speed impact driver.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |